1988-1995 130 LINKS FINE FINISH HELPS PREVENT PREMATURE WEAR
OF TIMING COMPONENTS
3DR130 $22.02
1987-1991 130 LINKS 1ST DES.
Cam Sprocket
S692 $17.69
1987-1991 38 TEETH 1ST DES. (2) REQ.
S734 $17.40
1987-1995 38 TEETH 2ND DES. (2) REQ.
Crank Sprocket
S653 $16.55
1987-1991 19 TEETH 1ST DES.
S747 $15.80
1987-1995 19 TEETH 2ND DES.
Tensioner
BT188 $42.91
1987-1991 1ST DES.
Guide
BG304 $8.28
2ND DES. 23MM WIDE- RIGHT HAND
BG305 $12.66
2ND DES. 23MM WIDE- LEFT HAND
BG306 $6.92
2ND DES. 23MM WIDE- UPPER
Timing Kit
3-383SB $127.12
KIT INCLUDES [383], (2) [S734], [S747], [BG304], [BG305] &
[BG306] UPDATED TIMING CHAIN WILL NOT FIT ORIGINAL WATER
PUMP SPROCKET USE GM 24570609 WITH 383 $66.57 CHAIN. MELLING
DOES NOT FURNISH
3pc Timing Set
3-383S $95.27
1992-1995 INCLUDES [383], (2) [S734] & [S747] 2ND DES.
3-3DR130 $71.42
1987-1991 INCLUDES [3DR130], (2) [S692] & [S653] 1ST DES.
KIT INCLUDES 1-[SPC-10] CAM, 8-[JB-2077] LIFTERS & 4OZ MELL
LUBE
Torque Camshaft
MTP2 $126.63
NOT CALIFORNIA COMPLIANT. HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
Cam Thrust Plate Spacer
MG221 $4.05
-
Mell Lube
M10012 $4.93
-
Lifters
JB2077 $2.85
HYD.
Push Rods
MPR338 $1.22
-
Intake Valve
V1438 $7.00
Head Dia. 1.720
Exhaust Valve
V1437 $10.37
Head Dia. 1.500
Valve Springs
VS170 $4.45
-
Valve Locks
VL200 $1.21
-
Rocker Arm Kit
MRK546 $11.14
KIT INCLUDES 1-[MR-806], 1-[MRM-1753] & 1-[MRM-1796]
1979-1980 NOT CALIFORNIA COMPLIANT. HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
Cam Thrust Plate Spacer
MG221 $4.05
-
Mell Lube
M10012 $4.93
-
Lifters
JB2077 $2.85
1979-1980 HYD.
JB969 $6.81
1978 HYD.
Push Rods
MPR317 $2.27
1978
MPR338 $1.22
1979-1980
Intake Valve
V1360 $6.47
1978 Head Dia. 1.720
V1438 $7.00
1979-1980 Head Dia. 1.720
Exhaust Valve
V1359 $15.85
1978 Head Dia. 1.500
V1437 $10.37
1979-1980 Head Dia. 1.500
Valve Springs
VS170 $4.45
-
Valve Locks
VL200 $1.21
-
Rocker Arm Kit
MRK546 $11.14
KIT INCLUDES 1-[MR-806], 1-[MRM-1753] & 1-[MRM-1796]
NOT CALIFORNIA COMPLIANT. HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
Cam Thrust Plate Spacer
MG221 $4.05
-
Mell Lube
M10012 $4.93
-
Lifters
JB2077 $2.85
HYD.
Push Rods
MPR338 $1.22
1980-1981
MPR347 $4.14
1982-1983
Intake Valve
V1438 $7.00
Head Dia. 1.720
Exhaust Valve
V1437 $10.37
Head Dia. 1.500
Valve Springs
VS170 $4.45
-
Valve Locks
VL200 $1.21
-
Rocker Arms
MR865 $9.14
1981-1983
Rocker Arm Kit
MRK409 $11.91
1981-1983 KIT INCLUDES 1-[MR-865] & 1-[MRM-1716]
MRK546 $11.14
1980 KIT INCLUDES 1-[MR-806], 1-[MRM-1753] & 1-[MRM-1796]
1982-1984 NOT CALIFORNIA COMPLIANT. HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
Cam Thrust Plate Spacer
MG221 $4.05
-
Mell Lube
M10012 $4.93
-
Lifters
JB2077 $2.85
1982-1984 HYD.
JB2079 $14.23
1984-1992 HYD. ROLLER
Push Rods
MPR282 $1.69
1984-1986 W/ROLLER LIFTERS
MPR347 $4.14
1982-1984 W/O ROLLER LIFTERS
MPR372 $2.11
1987-1992
Intake Valve
V1438 $7.00
1982-1983 Head Dia. 1.720
V1438 $7.00
1984-1986 Head Dia. 1.720 1ST DES. W/.3422 DIA. VALVE STEM
V1592 $9.41
1989-1992 Head Dia. 1.720
Exhaust Valve
V1437 $10.37
1982-1983 Head Dia. 1.500
V1437 $10.37
1984-1986 Head Dia. 1.500 1ST DES. W/.3419 DIA. VALVE STEM
V1550 $9.13
1984-1986 Head Dia. 1.500 2ND DES. W/.3132 DIA. VALVE STEM
2.8-7 (173) ENG - 1980 - V6 - 89 MM Bore (CHEVROLET)
Oil Pump
M95B $68.15
-
M95HV $126.98
HI VOL PUMP-20% ADDL VOL OF OIL THAN STOCK PUMP
M95HVS3 $160.56
HI VOL PUMP-20% ADDL VOL OF OIL THAN STOCK PUMP. INCLUDES
SCREEN.
Pump Kit
K95B $52.41
EXC. HI VOL
Screen Assy
95S3 $14.26
HI VOL
95S4 $15.68
EXC. HI VOL
Intermediate Shaft
IS95 $8.89
-
Nylon Shaft Guide
M55024 $0.67
-
Camshaft
CCS30 $61.77
HYD.
Camshaft Lifter Kit
CLCCS30 $151.47
KIT INCLUDES 1-[CCS-30] CAM, 12-[JB-2095] LIFTERS & 4OZ MELL
LUBE
Torque Camshaft
MTC5 $152.42
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
Torque Cam Lifter Kit
CLMTC5 $219.29
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTC-5] CAM, 12-[JB-2095]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CHECK FOR COIL BIND. CLASS
I HYD. NOT COMPUTER COMPATIBLE. IMPROVES LOW-MID. PERF.
CAM LIFT .280 INT. .295 EXH.
Mell Lube
M10012 $4.93
-
Lifters
JB2095 $5.90
HYD.
Push Rods
MPR342 $2.56
-
Intake Valve
V1395 $5.42
Head Dia. 1.600
Exhaust Valve
V1394 $6.90
Head Dia. 1.307
Valve Springs
VS580 $5.37
-
Valve Locks
VL200 $1.21
-
Rocker Arms
MR864 $8.00
-
Rocker Arm Kit
MRK407 $9.87
KIT INCLUDES 1-[MR-864], 1-[MRM-1721], 1-[MRM-1720] & 1-
[MRM-1723]
HI VOL PUMP-20% ADDL VOL OF OIL THAN STOCK PUMP. INCLUDES
SCREEN.
Pump Kit
K95B $52.41
EXC. HI VOL
Screen Assy
95S2 $10.27
1985-1986 EXC. HI VOL
95S3 $14.26
HI VOL
95S6 $14.17
1987-1989 EXC. HI VOL
Intermediate Shaft
IS95 $8.89
-
Nylon Shaft Guide
M55024 $0.67
-
Camshaft
MC1290 $203.52
HYD.
Camshaft Lifter Kit
CLMC1290 $238.36
KIT INCLUDES 1-[MC1290] CAM, 12-[JB-2095] LIFTERS & 4OZ MELL
LUBE
Torque Camshaft
MTC5 $152.42
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
Torque Cam Lifter Kit
CLMTC5 $219.29
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTC-5] CAM, 12-[JB-2095]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CHECK FOR COIL BIND. CLASS
I HYD. NOT COMPUTER COMPATIBLE. IMPROVES LOW-MID. PERF.
CAM LIFT .280 INT. .295 EXH.
Mell Lube
M10012 $4.93
-
Lifters
JB2095 $5.90
HYD.
Push Rods
MPR342 $2.56
1985-1986
MPR375 $2.27
1987-1989 INT.
MPR376 $2.59
1987-1989 EXH.
Intake Valve
V1481 $9.03
1985-1986 Head Dia. 1.718
V1561 $3.58
1987-1989 Head Dia. 1.718
Exhaust Valve
V1480 $11.64
1985-1986 Head Dia. 1.425
Valve Springs
VS2207 $3.57
1987-1989
VS590 $2.75
1985-1986
Valve Locks
VL200 $1.21
1985-1986
VL710 $1.75
1987-1989
Rocker Arms
MR864 $8.00
-
Rocker Arm Kit
MRK407 $9.87
KIT INCLUDES 1-[MR-864], 1-[MRM-1721], 1-[MRM-1720] & 1-
[MRM-1723]
Rocker Arm Ball
MRM1721 $0.67
-
Rocker Arm Nut
MRM1720 $1.84
1985-1986
MRM1723 $0.92
1987-1989
Rocker Arm Stud
MRDS948 $3.77
1985-1986 57MM OVERALL LENGTH, 10MM DIAMETER WITH HEX NUT ADJ.
Chain
372 $28.36
1985-1987 64 LINKS FIRENZA
372 $28.36
1987-1989 64 LINKS CUTLASS CIERA
373 $31.78
1986 64 LINKS CUTLASS CIERA
Cam Sprocket
S506 $8.95
1986 40 TEETH CUTLASS CIERA
S620 $17.96
1985-1987 40 TEETH FIRENZA
Cam Sprocket
S620 $17.96
1987-1989 40 TEETH CUTLASS CIERA
Crank Sprocket
S511 $10.26
1986 20 TEETH CUTLASS CIERA
S619 $14.21
1985-1987 20 TEETH FIRENZA
S619 $14.21
1987-1989 20 TEETH CUTLASS CIERA
Damper
BD131 $8.94
1985-1986 FIRENZA
BD131 $8.94
1987-1989
BD59 $7.62
1985-1986 EXC. FIRENZA
3pc Timing Set
3-372S $50.71
1985-1987 INCLUDES [372], [S620] & [S619] FIRENZA
3-372S $50.71
1987-1989 INCLUDES [372], [S620] & [S619] CUTLASS CIERA
3-373S $44.35
1986 INCLUDES [373], [S506] & [S511] CUTLASS CIERA
2.8-X (173) ENG - 1981-86 - V6 - 89 MM Bore (CHEVROLET)
-
Oil Pump
M95B $68.15
-
M95HV $126.98
HI VOL PUMP-20% ADDL VOL OF OIL THAN STOCK PUMP
M95HVS3 $160.56
HI VOL PUMP-20% ADDL VOL OF OIL THAN STOCK PUMP. INCLUDES
SCREEN.
Pump Kit
K95B $52.41
EXC. HI VOL
95S2 $10.27
1982-1986 EXC. HI VOL
95S3 $14.26
HI VOL
95S4 $15.68
1981 EXC. HI VOL
Intermediate Shaft
IS95 $8.89
-
Nylon Shaft Guide
M55024 $0.67
-
Camshaft
CCS30 $61.77
HYD.
Camshaft Lifter Kit
CLCCS30 $151.47
KIT INCLUDES 1-[CCS-30] CAM, 12-[JB-2095] LIFTERS & 4OZ MELL
LUBE
Torque Camshaft
MTC5 $152.42
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
Torque Cam Lifter Kit
CLMTC5 $219.29
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTC-5] CAM, 12-[JB-2095]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CHECK FOR COIL BIND. CLASS
I HYD. NOT COMPUTER COMPATIBLE. IMPROVES LOW-MID. PERF.
CAM LIFT .280 INT. .295 EXH.
Mell Lube
M10012 $4.93
-
Lifters
JB2095 $5.90
HYD.
Push Rods
MPR342 $2.56
-
Intake Valve
V1395 $5.42
Head Dia. 1.600
Exhaust Valve
V1394 $6.90
Head Dia. 1.307
Valve Springs
VS590 $2.75
-
Valve Locks
VL200 $1.21
-
Rocker Arms
MR864 $8.00
-
Rocker Arm Kit
MRK407 $9.87
KIT INCLUDES 1-[MR-864], 1-[MRM-1721], 1-[MRM-1720] & 1-
[MRM-1723]
2.8-Z (173) ENG - 1982-84 - V6 - 89 MM Bore (CHEVROLET)
-
Oil Pump
M95B $68.15
-
M95HV $126.98
HI VOL PUMP-20% ADDL VOL OF OIL THAN STOCK PUMP
M95HVS3 $160.56
HI VOL PUMP-20% ADDL VOL OF OIL THAN STOCK PUMP. INCLUDES
SCREEN.
Pump Kit
K95B $52.41
EXC. HI VOL
Screen Assy
95S2 $10.27
EXC. HI VOL
95S3 $14.26
HI VOL
Intermediate Shaft
IS95 $8.89
-
Nylon Shaft Guide
M55024 $0.67
-
Camshaft
MC1290 $203.52
HYD.
Camshaft Lifter Kit
CLMC1290 $238.36
KIT INCLUDES 1-[MC1290] CAM, 12-[JB-2095] LIFTERS & 4OZ MELL
LUBE
Torque Camshaft
MTC5 $152.42
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
Torque Cam Lifter Kit
CLMTC5 $219.29
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTC-5] CAM, 12-[JB-2095]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CHECK FOR COIL BIND. CLASS
I HYD. NOT COMPUTER COMPATIBLE. IMPROVES LOW-MID. PERF.
CAM LIFT .280 INT. .295 EXH.
Mell Lube
M10012 $4.93
-
Lifters
JB2095 $5.90
HYD.
Push Rods
MPR342 $2.56
-
Intake Valve
V1481 $9.03
Head Dia. 1.718
Exhaust Valve
V1480 $11.64
Head Dia. 1.425
Valve Springs
VS590 $2.75
-
Valve Locks
VL200 $1.21
-
Rocker Arms
MR864 $8.00
-
Rocker Arm Kit
MRK407 $9.87
KIT INCLUDES 1-[MR-864], 1-[MRM-1721], 1-[MRM-1720] & 1-
[MRM-1723]
HI Vol Kit. Provides 29% greater volume. This is a complete kit
that includes longer gears,spacer,gaskets,springs &
instructions. May require removing timing cover for installation.
Requires hand tools & drill (Drill bit included) to
install.
Gear Thrust Plate
P20L $31.67
PROVIDES NEW WEARING SURFACE FOR OUR [K-20LHV] OIL PUMP
KIT. [P-20L] KIT INCLUDES CAST IRON THRUST PLATE, MOUNTING
GASKET, PROPER LENGTH SCREWS & INSTRUCTION SHEET.
Screen Assy
20IS4 $18.97
-
Camshaft
SBC12 $106.43
HYD.
Camshaft Lifter Kit
CLSBC12 $162.12
KIT INCLUDES 1-[SBC-12] CAM, 12-[JB-969] LIFTERS & 4OZ MELL
LUBE
Torque Camshaft
MTB1 $206.53
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES MID-RANGE PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
MTB2 $227.26
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .265 INT .280
EXH.
Torque Cam Lifter Kit
CLMTB1 $268.50
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTB-1] CAM, 12-[JB-969]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES MID RANGE PERF. CAM LIFT .280 INT.
.295 EXH.
CLMTB2 $326.52
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTB-2] CAM, 12-[JB-969]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .265 INT.
.280 EXH.
KIT INCLUDES 1-[MC1290] CAM, 12-[JB-2095] LIFTERS & 4OZ MELL
LUBE
Torque Camshaft
MTC5 $152.42
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
Torque Cam Lifter Kit
CLMTC5 $219.29
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTC-5] CAM, 12-[JB-2095]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CHECK FOR COIL BIND. CLASS
I HYD. NOT COMPUTER COMPATIBLE. IMPROVES LOW-MID. PERF.
CAM LIFT .280 INT. .295 EXH.
PROVIDES NEW WEARING SURFACE FOR OUR [K-20I], [K- 20IHV],
[K-20J] & [K-20JHV] OIL PUMP KIT. [P-20I] KIT INCLUDES
CAST IRON THRUST PLATE, MOUNTING GASKET, PROPERLENGTH SCREWS
& INSTRUCTION SHEET
Camshaft
SBOT-1 $131.78
ALL F-85 MODELS HYD.
Mell Lube
M10012 $4.93
-
Lifters
JB896 $25.34
HYD.
Valve Springs
VS570 $4.25
-
Chain
359 $18.87
54 LINKS
Crank Sprocket
S323 $7.81
20 TEETH
3pc Timing Set
3-359S $49.10
INCLUDES [359], [S334] & [S323]
35
225 ENG - 1964-65 - V6 - 3 3/4 Bore (BUICK)
-
Pump Kit
K20I $30.15
REPAIR KIT FOR STANDARD VOLUME OIL PUMPS
K20IHV $76.32
HI Vol Kit. Provides 29% greater volume. This is a complete kit
that includes longer gears,spacer,gaskets,springs &
instructions. May require removing timing cover for installation.
Requires hand tools & drill (Drill bit included) to
install.
K20IPHV $141.27
INCLUDES [K-20IHV] & [P-20I] THRUST PLATE KIT
Gear Thrust Plate
P20I $36.51
PROVIDES NEW WEARING SURFACE FOR OUR [K-20I], [K- 20IHV],
[K-20J] & [K-20JHV] OIL PUMP KIT. [P-20I] KIT INCLUDES
CAST IRON THRUST PLATE, MOUNTING GASKET, PROPER LENGTH
SCREWS & INSTRUCTION SHEET
HI Vol Kit. Provides 29% greater volume. This is a complete kit
that
includes longer gears,spacer,gaskets,springs & instructions.
May
require removing timing cover for installation. Requires hand
tools &
drill (Drill bit included) to install.
K20IPHV $141.27
INCLUDES [K-20IHV] & [P-20I] THRUST PLATE KIT
Gear Thrust Plate
P20I $36.51
PROVIDES NEW WEARING SURFACE FOR OUR [K-20I], [K- 20IHV],
[K-20J] & [K-20JHV] OIL PUMP KIT. [P-20I] KIT INCLUDES
CAST IRON THRUST PLATE, MOUNTING GASKET, PROPER LENGTH
SCREWS & INSTRUCTION SHEET
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES MID-RANGE PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
MTB2 $227.26
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .265 INT .280
EXH.
Torque Cam Lifter Kit
CLMTB1 $268.50
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTB-1] CAM, 12-[JB-969]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES MID RANGE PERF. CAM LIFT .280 INT.
.295 EXH.
CLMTB2 $326.52
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTB-2] CAM, 12-[JB-969]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .265 INT.
.280 EXH.
HI Vol Kit. Provides 29% greater volume. This is a complete kit
that includes longer gears,spacer,gaskets,springs &
instructions. May require removing timing cover for installation.
Requires hand tools & drill (Drill bit included) to
install.
Gear Thrust Plate
P20L $31.67
PROVIDES NEW WEARING SURFACE FOR OUR [K-20LHV] OIL PUMP
KIT. [P-20L] KIT INCLUDES CAST IRON THRUST PLATE, MOUNTING
GASKET, PROPER LENGTH SCREWS & INSTRUCTION SHEET.
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES MID-RANGE PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
MTB2 $227.26
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .265 INT .280
EXH.
Torque Cam Lifter Kit
CLMTB1 $268.50
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTB-1] CAM, 12-[JB-969]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES MID RANGE PERF. CAM LIFT .280 INT. .295
EXH.
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTB-2] CAM, 12-[JB-969]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .265 INT.
.280 EXH.
HI Vol Kit. Provides 29% greater volume. This is a complete kit
that
includes longer gears,spacer,gaskets,springs & instructions.
May
require removing timing cover for installation. Requires hand
tools &
drill (Drill bit included) to install.
K20IPHV $141.27
INCLUDES [K-20IHV] & [P-20I] THRUST PLATE KIT EXC. FWD
Gear Thrust Plate
P20I $36.51
PROVIDES NEW WEARING SURFACE FOR OUR [K-20I], [K- 20IHV],
[K-20J] & [K-20JHV] OIL PUMP KIT. [P-20I] KIT INCLUDES
CAST IRON THRUST PLATE, MOUNTING GASKET, PROPER LENGTH
SCREWS & INSTRUCTION SHEET EXC. FWD
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES MID-RANGE PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
MTB2 $227.26
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .265 INT .280
EXH.
Torque Cam Lifter Kit
CLMTB1 $268.50
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTB-1] CAM, 12-[JB-969]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES MID RANGE PERF. CAM LIFT .280 INT.
.295 EXH.
CLMTB2 $326.52
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTB-2] CAM, 12-[JB-969]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .265 INT.
.280 EXH.
HI Vol Kit. Provides 29% greater volume. This is a complete kit
that includes longer gears,spacer,gaskets,springs &
instructions. May require removing timing cover for installation.
Requires hand tools & drill (Drill bit included) to
install.
K20IPHV $141.27
INCLUDES [K-20IHV] & [P-20I] THRUST PLATE KIT EXC. FWD
Gear Thrust Plate
P20I $36.51
PROVIDES NEW WEARING SURFACE FOR OUR [K-20I], [K- 20IHV],
[K-20J] & [K-20JHV] OIL PUMP KIT. [P-20I] KIT INCLUDES
CAST IRON THRUST PLATE, MOUNTING GASKET, PROPER LENGTH
SCREWS & INSTRUCTION SHEET EXC. FWD
Screen Assy
20IS1 $26.86
1ST DES. W/4.5" DEEP OIL PAN
Cam Button
CB100 $17.33
CAM BUTTON WITH SPRING
Mell Lube
M10012 $4.93
-
Lifters
JB969 $6.81
HYD.
Push Rods
MPR103B $2.50
-
MPR387 $3.83
.035 O/S
MPR389 $2.62
.060 O/S
Intake Valve
V1353 $4.42
Head Dia. 1.625
Exhaust Valve
V1363 $7.52
Head Dia. 1.425 IN 1975 & 76 OEM VALVES HAD A .412"
VALVE STEM LOCKING GROOVE. OEM HAS REPLACED THIS VALVE
W/.125" VALVE STEM LOCKING GROOVE. WHEN REPLACING A
.412" VALVE W/.125" VALVE, YOU MUST REPLACE THE VALVE
LOCKS & RETAINER. VL-200 $1.32 LOCKS & 1254900 OEM RETAINER.
Valve Springs
VS2219 $2.90
W/DAMPER
VS490 $1.76
W/O DAMPER
Valve Locks
VL200 $1.21
1977
Rocker Arms
MR813 $3.51
RIGHT HAND
MR814 $3.80
LEFT HAND
Rocker Arm Kit
MRK542L $8.92
KIT INCLUDES 1-[MR-814] & 1-[MRM-1724] LEFT HAND
MRK542R $5.52
KIT INCLUDES 1-[MR-813] & 1-[MRM-1724] RIGHT HAND
Chain
359 $18.87
54 LINKS
Crank Sprocket
S323 $7.81
20 TEETH
Damper
BD44 $5.93
RIGHT HAND W/SPRING
BD45 $4.36
LEFT HAND
3pc Timing Set
3-359S $49.10
INCLUDES [359], [S334] & [S323] NON-INTEGRAL DIST. DRIVE
GEAR
HI Vol Kit. Provides 29% greater volume. This is a complete kit
that
includes longer gears,spacer,gaskets,springs & instructions.
May
require removing timing cover for installation. Requires hand
tools &
drill (Drill bit included) to install.
K20IPHV $141.27
INCLUDES [K-20IHV] & [P-20I] THRUST PLATE KIT
Gear Thrust Plate
P20I $36.51
PROVIDES NEW WEARING SURFACE FOR OUR [K-20I], [K- 20IHV],
[K-20J] & [K-20JHV] OIL PUMP KIT. [P-20I] KIT INCLUDES
CAST IRON THRUST PLATE, MOUNTING GASKET, PROPER LENGTH
SCREWS & INSTRUCTION SHEET
Screen Assy
20IS2 $28.54
1982-1983 EXC. TORONADO 2ND DES. W/5.25" DEEP OIL PAN
Camshaft
SBC12 $106.43
HYD.
Camshaft Lifter Kit
CLSBC12 $162.12
KIT INCLUDES 1-[SBC-12] CAM, 12-[JB-969] LIFTERS & 4OZ MELL
LUBE
Torque Camshaft
MTB1 $206.53
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES MID-RANGE PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH.
MTB2 $227.26
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .265 INT .280
EXH.
Torque Cam Lifter Kit
CLMTB1 $268.50
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTB-1] CAM, 12-[JB-969]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES MID RANGE PERF. CAM LIFT .280 INT. .295
EXH.
Torque Cam Lifter Kit
CLMTB2 $326.52
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTB-2] CAM, 12-[JB-969]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .265 INT.
.280 EXH.
2002-2004 MANUFACTURED FOR THE 2ND DESIGN PICK UP TUBE
ASSEMBLY, DO NOT REUSE OLD COVER OR PICK UP TUBE ASSEMBLY
Screen Assy
339S $49.12
2002 1ST DESIGN WITH O RING SEAL. NOT FOR USE WITH K322
$169.99 OIL PUMP KIT.
358S $52.23
2003-2004 2ND DESIGN WITH FACE SEAL USE WITH K322 $169.99 OIL
PUMP KIT
Mell Lube
M10012 $4.93
-
50
260-F & 8 ENG - 1975-82 - 8 Cyl. - 3.500 Bore
-
Oil Pump
M22F $114.26
-
M22FHV $181.07
HI VOL PUMP (20% ADDL VOL OF OIL) NOTE: THIS HI VOL PUMP
IS MANUFACTURED W/BOLT ON TYPE FLANGE AND A CHAMFERED HOLE.
EITHER A BOLT ON OR PRESS IN SCREEN CAN BE USED.
Pump Kit
K22F $42.79
EXC. HI VOL
Screen Assy
22FHVS $44.92
BOLT ON SCREEN W/3/4" PICK UP TUBE- USE W/HI VOL PUMP
22FS $31.75
PRESS IN SCREEN W/5/8" PICK UP TUBE, CAN BE USED IN EITHER
STOCK OR HI VOL PUMP
Intermediate Shaft
IS22F $14.18
-
Camshaft
SOC10 $152.77
HYD.
Camshaft Lifter Kit
CLSOC10
KIT INCLUDES 1-[SOC-10] CAM, 16-[JB-951] LIFTERS & 4OZ MELL
LUBE
Torque Camshaft
MTO1 $157.33
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CAM LIFT .280 INT. .295 EXH.
Torque Cam Lifter Kit
CLMTO1 $276.55
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTO-1] CAM, 16-[JB-951]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-720]
SPRING W/INSTALLED HGT. OF 1.67 CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .280 INT.
.295 EXH.
Mell Lube
M10012 $4.93
-
Lifters
JB951 $5.88
HYD.
Push Rods
MPR307 $2.62
1975-1979
MPR343 $2.09
1980-1982
Intake Valve
V1323 $5.45
Head Dia. 1.522
Exhaust Valve
V1322 $6.85
Head Dia. 1.300
Valve Springs
VS720 $3.01
-
Valve Locks
VL200 $1.21
-
Rocker Arms
MR890 $10.27
1975-1979
MR891 $3.58
1980-1982
Rocker Arm Kit
MRK540-1 $25.28
1975-1979 KIT INCLUDES 2-[MR-890] & 1-[MRM-1798] PIVOT
HI VOL PUMP (20% ADDL VOL OF OIL) NOTE: THIS HI VOL PUMP IS MANUFACTURED
W/BOLT ON TYPE FLANGE AND A CHAMFERED HOLE. EITHER A BOLT ON
OR PRESS IN SCREEN CAN BE USED.
M22G $123.94
-
Pump Kit
K22G $35.16
EXC. HI VOL
Screen Assy
22FHVS $44.92
BOLT ON SCREEN W/3/4" PICK UP TUBE- USE W/HI VOL PUMP
22FS $31.75
PRESS IN SCREEN W/5/8" PICK UP TUBE, CAN BE USED IN EITHER
STOCK OR HI VOL PUMP
HI VOL PUMP-25% ADDL VOL OF OIL THAN STOCK PUMP (MUST USE
IS SHAFT W/STEEL GUIDE) 5/8" SCREEN INLET
Pump Kit
K55 $38.10
EXC. HI VOL
Screen Assy
55S1 $14.18
-
Intermediate Shaft
IS55E $15.73
MANUFACTURED WITH STEEL SHAFT GUIDE- ELIMINATES NYLON SHAFT GUIDE
IS55G $12.56
USES M-55005 $1.22 NYLON SHAFT GUIDE
Nylon Shaft Guide
M55005 $1.18
USE W/[IS-55G]
Camshaft
CCS23 $117.56
HYD.
Camshaft Lifter Kit
CLCCS23 $240.07
KIT INCLUDES 1-[CCS-23] CAM, 16-[JB-817] LIFTERS & 4OZ MELL
LUBE
Torque Camshaft
MTC1 $103.21
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH. USE ONLY WITH CARBURETTED ENGINES.
Torque Cam Lifter Kit
CLMTC1 $231.95
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTC-1] CAM, 16-[JB-817]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72 CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .280 INT.
.295 EXH. USE ONLY WITH CARBURETTED ENGINES.
Mell Lube
M10012 $4.93
-
Lifters
JB817 $5.68
HYD.
Push Rods
MPR34B $1.83
-
Intake Valve
V0399 $4.12
Head Dia. 1.720 STEEL
V0399+15 $8.81
Head Dia. 1.720 .015 OVERSIZE STEEL VALVE
V0399+3 $6.37
Head Dia. 1.720 .003 OVERSIZE STEEL VALVE
Exhaust Valve
V1371 $8.06
Head Dia. 1.380
Valve Spring with Hydraulic Lifters
VS380 $3.24
STANDARD REPLACEMENT
VS739R $5.10
CHROME VANADIUM
Valve Locks
VL200 $1.21
-
Rocker Arms
MR842 $6.53
-
Rocker Arm Kit
MRK401 $7.00
KIT INCLUDES 1-[MR-842], 1-[MRM-1731] & 1-[MRM-1786]
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH. USE ONLY WITH CARBURETTED ENGINES.
Torque Cam Lifter Kit
CLMTC1 $231.95
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTC-1] CAM, 16-[JB-817]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72 CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .280 INT.
.295 EXH. USE ONLY WITH CARBURETTED ENGINES.
Mell Lube
M10012 $4.93
-
Lifters
JB817 $5.68
HYD.
Push Rods
MPR34B $1.83
-
Intake Valve
V0399 $4.12
1977-1978 Head Dia. 1.720 STEEL 305-U
V0399 $4.12
1979 Head Dia. 1.720 STEEL 305-G
V0399+15 $8.81
1977-1978 Head Dia. 1.720 .015 OVERSIZE STEEL VALVE 305-U
V0399+15 $8.81
1979 Head Dia. 1.720 .015 OVERSIZE STEEL VALVE 305-G
V0399+3 $6.37
1977-1978 Head Dia. 1.720 .003 OVERSIZE STEEL VALVE 305-U
V0399+3 $6.37
1979 Head Dia. 1.720 .003 OVERSIZE STEEL VALVE 305-G
V1393 $8.25
1978-1979 Head Dia. 1.840 305-H
V1393 $8.25
1980-1987 Head Dia. 1.840
Exhaust Valve
V1192 $8.32
Head Dia. 1.500
Valve Springs
VS580 $5.37
1977 EXH. ONLY
Valve Spring with Hydraulic Lifters
VS380 $3.24
1977 STANDARD REPLACEMENT INT.
VS380 $3.24
1978-1987 STANDARD REPLACEMENT INT. & EXH.
VS739R $5.10
1977 CHROME VANADIUM INT.
VS739R $5.10
1978-1987 CHROME VANADIUM INT. AND EXH.
Valve Locks
VL200 $1.21
-
Rocker Arms
MR842 $6.53
-
Rocker Arm Kit
MRK401 $7.00
KIT INCLUDES 1-[MR-842], 1-[MRM-1731] & 1-[MRM-1786]
Rocker Arm Ball
MRM1731 $0.80
-
Rocker Arm Nut
MRM1786 $0.72
-
Rocker Arm Stud
MRDS921 $4.64
.003 O/S
Chain
163 $14.17
58 LINKS H.D.
499 $18.97
1977-1984 46 LINKS
506 $20.15
1985-1987 46 LINKS
Cam Sprocket
S288 $25.20
44 TEETH H.D.
S390 $10.41
36 TEETH
Crank Sprocket
S289 $11.30
22 TEETH H.D.
S391 $5.37
18 TEETH
3pc Timing Set
3-163S $42.71
INCLUDES [163], [S288] & [S289] H.D.
3-499S $31.69
1977-1984 INCLUDES [499], [S390] & [S391]
3-506SA $31.56
1985-1987 INCLUDES [506], [S390] & [S391]
Page 629. OLDSMOBILE (Continued)
Line
Part Title
Part No
Description
59
5.0-E (305) ENG - 1991-92 - 8 Cyl. - 3.736 Bore
-
Oil Pump
M55 $41.17
5/8" SCREEN INLET STANDARD VOLUME
M55HV $55.59
HI VOL PUMP-25% ADDL VOL OF OIL THAN STOCK PUMP (MUST USE
IS SHAFT W/STEEL GUIDE) 5/8" SCREEN INLET
Pump Kit
K55 $38.10
EXC. HI VOL
Oil Filter Adapter
MFA350 $25.34
ADAPTER NOT FOR USE WITH 90° FILTER APPLICATIONS. FOR LARGE
DIAMETER VERTICAL FILTER ONLY.
Screen Assy
55S1 $14.18
-
Intermediate Shaft
IS55E $15.73
MANUFACTURED WITH STEEL SHAFT GUIDE- ELIMINATES NYLON SHAFT GUIDE
IS55G $12.56
USES M-55005 $1.22 NYLON SHAFT GUIDE
Nylon Shaft Guide
M55005 $1.18
USE W/[IS-55G]
Camshaft
CCS39 $400.52
HYD. ROLLER HYD. ROLLER
Mell Lube
M10012 $4.93
-
Lifters
JB2079 $14.23
HYD. ROLLER
Push Rods
MPR373 $2.45
-
Intake Valve
V1393 $8.25
Head Dia. 1.840
Exhaust Valve
V1192 $8.32
Head Dia. 1.500
V1206 $20.45
Head Dia. 1.500 OPTIONAL (STELLITE) SAME APPLICATION AS [V1192]
Valve Spring with Hydraulic Lifters
VS380 $3.24
STANDARD REPLACEMENT
VS739R $5.10
CHROME VANADIUM
Valve Locks
VL200 $1.21
-
Rocker Arms
MR926 $6.03
-
Rocker Arm Kit
MRK651 $5.95
KIT INCLUDES 1-[MR-926], 1-[MRM-1731] & 1-[MRM-1786]
HI VOL PUMP (20% ADDL VOL OF OIL) NOTE: THIS HI VOL PUMP
IS MANUFACTURED W/BOLT ON TYPE FLANGE AND A CHAMFERED HOLE.
EITHER A BOLT ON OR PRESS IN SCREEN CAN BE USED.
Pump Kit
K22F $42.79
EXC. HI VOL
Screen Assy
22FHVS $44.92
BOLT ON SCREEN W/3/4" PICK UP TUBE- USE W/HI VOL PUMP- RWD
ONLY
22FS $31.75
PRESS IN SCREEN W/5/8" PICK UP TUBE, CAN BE USED IN EITHER
STOCK OR HI VOL PUMP- RWD ONLY
22FS3 $19.48
PRESS IN SCREEN- CAN BE USED IN STOCK OR HI VOL PUMP- FWD ONLY
1980-1984 NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER
COMPATIBLE, IMPROVES LOW-MID. PERF. USE ONLY IN 1987 AND
OLDER S.B. CARBURETTED V8 ENGINES. CAM LIFT .280 INT. .295
EXH. W/VIN "Y".
MTO1 $157.33
1983-1985 NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER
COMPATIBLE, IMPROVES LOW-MID. PERF. USE ONLY IN 1987 AND
OLDER S.B. CARBURETTED V8 ENGINES. CAM LIFT .280 INT. .295
EXH. W/VIN "9".
Torque Cam Lifter Kit
CLMTO1 $276.55
1980-1984 NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1- [MTO-1]
CAM, 16-[JB-951] LIFTERS & 4OZ MELL LUBE. CHECK FOR
COIL BIND. USE [VS-720] SPRING W/INSTALLED HGT. OF 1.67
CLASS I HYD. NOT COMPUTER COMPATIBLE, IMPROVES LOW-MID.
PERF. USE ONLY IN 1987 AND OLDER S.B. CARBURETTED V8 ENGINES.
CAM LIFT .280 INT. .295 EXH. VIN CODE "Y".
CLMTO1 $276.55
1983-1995 NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1- [MTO-1]
CAM, 16-[JB-951] LIFTERS & 4OZ MELL LUBE. CHECK FOR
COIL BIND. USE [VS-720] SPRING W/INSTALLED HGT. OF 1.67
CLASS I HYD. NOT COMPUTER COMPATIBLE, IMPROVES LOW-MID.
PERF. USE ONLY IN 1987 AND OLDER S.B. CARBURETTED V8 ENGINES.
CAM LIFT .280 INT. .295 EXH. VIN CODE "9".
Mell Lube
M10012 $4.93
-
Lifters
JB2104 $15.84
1985 HYD. W/VIN CODE "Y"
JB2104 $15.84
1986-1990 HYD. ROLLER
JB951 $5.88
1980-1984 HYD.
JB951 $5.88
1985 HYD. W/VIN CODE "9"
Push Rods
MPR343 $2.09
1980-1984
MPR343 $2.09
1985 W/VIN CODE "9"
MPR365 $2.34
1985 W/VIN CODE "Y"
MPR365 $2.34
1986-1990
Intake Valve
V1450 $8.62
Head Dia. 1.750
Exhaust Valve
V1354 $9.52
Head Dia. 1.502 5.0-Y
V1549 $24.17
Head Dia. 1.505 5.0-9
Valve Springs
VS1100 $6.12
1983-1987 VIN CODE "9"
VS720 $3.01
VIN CODE "Y"
Valve Locks
VL200 $1.21
-
Rocker Arms
MR891 $3.58
-
Rocker Arm Kit
MRK550-2 $14.12
KIT INCLUDES 2-[MR-891] & 1-[MRM-1798]
Rocker Arm Pivot
MRM1798 $2.85
-
Chain
498 $25.20
48 LINKS
Cam Sprocket
S348 $15.66
36 TEETH
Crank Sprocket
S349 $4.72
18 TEETH
3pc Timing Set
3-498SC $60.36
INCLUDES [498], [S348] & [S349]
Page 631. OLDSMOBILE (Continued)
Line
Part Title
Part No
Description
61
324 ENG - 1954-56 - 8 Cyl. - 3 7/8 Bore
-
Oil Filter Adapter
MFA350 $25.34
ADAPTER NOT FOR USE WITH 90° FILTER APPLICATIONS. FOR LARGE
DIAMETER VERTICAL FILTER ONLY.
Mell Lube
M10012 $4.93
-
Push Rods
MPR91 $6.57
-
Chain
494 $22.07
48 LINKS
Crank Sprocket
S246 $39.56
18 TEETH
62
330 ENG - 1964-67 - 8 Cyl. - 3 15/16 Bore
-
Oil Pump
M22F $114.26
STOCK PUMP
M22FHV $181.07
HI VOL PUMP (20% ADDL VOL OF OIL) NOTE: THIS HI VOL PUMP
IS MANUFACTURED W/BOLT ON TYPE FLANGE AND A CHAMFERED HOLE.
EITHER A BOLT ON OR PRESS IN SCREEN CAN BE USED.
Pump Kit
K22F $42.79
EXC. HI VOL
Screen Assy
22FHVS $44.92
BOLT ON SCREEN W/3/4" PICK UP TUBE- USE W/HI VOL PUMP
22FS $31.75
PRESS IN SCREEN W/5/8" PICK UP TUBE, CAN BE USED IN EITHER
STOCK OR HI VOL PUMP
Intermediate Shaft
IS22F $14.18
-
Camshaft
MC1287 $249.39
1967 W/4BC EXC. O.A.I. HYD.
Mell Lube
M10012 $4.93
-
Lifters
JB951 $5.88
HYD.
Push Rods
MPR309-A
1967 .062 U/S W/4BC
MPR97 $4.00
1967 W/2BC
Intake Valve
V0969 $9.11
1965-1967 Head Dia. 1.875
Exhaust Valve
V0970 $14.35
1965-1967 Head Dia. 1.562
Valve Springs
VS720 $3.01
1964 W/STAMPED ROCKER ARMS 1965-67 ALL
Valve Locks
VL200 $1.21
-
Rocker Arms
MR890 $10.27
-
Rocker Arm Kit
MRK540-1 $25.28
1966-1967 KIT INCLUDES 2-[MR-890] & 1-[MRM-1798] PIVOT
HI Vol Kit. Provides 29% greater volume. This is a complete kit
that includes longer gears,spacer,gaskets,springs &
instructions. May require removing timing cover for installation.
Requires hand tools & drill (Drill bit included) to
install.
K20IPHV $141.27
INCLUDES [K-20IHV] & [P-20I] THRUST PLATE KIT
Oil Filter Adapter
MFA350 $25.34
ADAPTER NOT FOR USE WITH 90° FILTER APPLICATIONS. FOR
LARGE DIAMETER VERTICAL FILTER ONLY.
Gear Thrust Plate
P20I $36.51
PROVIDES NEW WEARING SURFACE FOR OUR [K-20I], [K- 20IHV],
[K-20J] & [K-20JHV] OIL PUMP KIT. [P-20I] KIT INCLUDES
CAST IRON THRUST PLATE, MOUNTING GASKET, PROPER LENGTH
SCREWS & INSTRUCTION SHEET
350. & R ENG - 1968-80 - 8 Cyl.
- 4.057 Bore (350 1968-76 EXC. OMEGA)(350-R 1977-80)
-
Oil Pump
M22F $114.26
STOCK PUMP
M22FHV $181.07
HI VOL PUMP (20% ADDL VOL OF OIL) NOTE: THIS HI VOL PUMP
IS MANUFACTURED W/BOLT ON TYPE FLANGE AND A CHAMFERED HOLE.
EITHER A BOLT ON OR PRESS IN SCREEN CAN BE USED.
Pump Kit
K22F $42.79
EXC. HI VOL
Screen Assy
22FHVS $44.92
BOLT ON SCREEN W/3/4" PICK UP TUBE- USE W/HI VOL PUMP- RWD
ONLY
22FS $31.75
PRESS IN SCREEN W/5/8" PICK UP TUBE, CAN BE USED IN EITHER
STOCK OR HI VOL PUMP- RWD ONLY
22FS3 $19.48
PRESS IN SCREEN- CAN BE USED IN STOCK OR HI VOL PUMP- FWD ONLY
Intermediate Shaft
IS22F $14.18
-
Camshaft
MC1287 $249.39
1968-1975 EXC. H.P. & 442 HYD.
ROC10 $113.01
1968-1970 W/O.A.I. (RAM AIR) HYD. OEM #402194
SOC9 $166.79
1976-1980 EXC. H.P. O.A.I.(RAM AIR) HYD.
Camshaft Lifter Kit
CLSOC9 $261.09
KIT INCLUDES 1-[SOC-9] CAM, 16-[JB-951] LIFTERS & 4OZ MELL
LUBE EXC. HI PERF. O.A.I. (RAM AIR)
Torque Camshaft
MTO1 $157.33
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CAM LIFT .280 INT. .295 EXH. (EXC.
HI PERF. O.A.I. RAM AIR)
Torque Cam Lifter Kit
CLMTO1 $276.55
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTO-1] CAM, 16-[JB-951]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-720]
SPRING W/INSTALLED HGT. OF 1.67 CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .280 INT.
.295 EXH. (EXC. HI PERF. O.A.I. RAM AIR)
Continued on Next Page
Page 633. OLDSMOBILE (Continued)
Line
Part Title
Part No
Description
64
350. & R ENG - 1968-80 - 8 Cyl.
- 4.057 Bore (350 1968-76 EXC. OMEGA)(350-R 1977-80)
(Continued)
-
Mell Lube
M10012 $4.93
-
Lifters
JB951 $5.88
HYD.
Push Rods
MPR307 $2.62
1968-1979
MPR343 $2.09
1980
Intake Valve
V0969 $9.11
1968-1972 Head Dia. 1.875 EXC. O.A.I.
V1263 $9.72
1973-1980 Head Dia. 1.875
V1457 $9.62
1968-1971 Head Dia. 1.995 W/O.A.I
Exhaust Valve
V0970 $14.35
1968-1971 Head Dia. 1.562 EXC. O.A.I.
V0974 $14.20
1968-1971 Head Dia. 1.624 W/O.A.I.
V1212 $15.03
1972 Head Dia. 1.622
V1324 $13.17
1973-1976 Head Dia. 1.622
V1354 $9.52
1977-1980 Head Dia. 1.502
Valve Springs
VS720 $3.01
EXC. HI PERF. O.A.I. (RAM AIR)
Valve Locks
VL200 $1.21
-
Rocker Arms
MR890 $10.27
1968-1979
MR891 $3.58
1980
Rocker Arm Kit
MRK540-1 $25.28
1968-1979 KIT INCLUDES 2-[MR-890] & 1-[MRM-1798] PIVOT
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72. CAM LIFT .280 INT. .295
EXH. USE ONLY WITH CARBURETTED ENGINES.
Torque Cam Lifter Kit
CLMTC1 $231.95
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTC-1] CAM, 16-[JB-817]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-380]
SPRING W/INSTALLED HGT. OF 1.72 CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .280 INT.
.295 EXH. USE ONLY WITH CARBURETTED ENGINES.
Mell Lube
M10012 $4.93
-
Lifters
JB817 $5.68
HYD.
Push Rods
MPR34B $1.83
-
Intake Valve
V0399 $4.12
1977 Head Dia. 1.720 STEEL 350-G
V0399+15 $8.81
1977 Head Dia. 1.720 .015 OVERSIZE STEEL VALVE 305-G
V0399+3 $6.37
1977 Head Dia. 1.720 .003 OVERSIZE STEEL VALVE 305-G
V1195 $6.81
1977-1979 Head Dia. 1.940 350-L
Exhaust Valve
V1192 $8.32
Head Dia. 1.500
V1206 $20.45
Head Dia. 1.500 OPTIONAL (STELLITE) SAME APPLICATION AS [V1192]
Valve Springs
VS580 $5.37
1977 EXH.
Valve Spring with Hydraulic Lifters
VS380 $3.24
1977 STANDARD REPLACEMENT INT.
VS380 $3.24
1978-1979 STANDARD REPLACEMENT INT. & EXH.
VS739R $5.10
1977 CHROME VANADIUM INT.
VS739R $5.10
1978-1979 CHROME VANADIUM INT. & EXH.
Valve Locks
VL200 $1.21
-
Rocker Arms
MR842 $6.53
-
Rocker Arm Kit
MRK401 $7.00
KIT INCLUDES 1-[MR-842], 1-[MRM-1731] & 1-[MRM-1786]
Rocker Arm Ball
MRM1731 $0.80
-
Rocker Arm Nut
MRM1786 $0.72
-
Rocker Arm Stud
MRDS921 $4.64
.003 O/S
Chain
163 $14.17
58 LINKS H.D.
499 $18.97
46 LINKS
Cam Sprocket
S288 $25.20
44 TEETH H.D.
S390 $10.41
36 TEETH
Crank Sprocket
S289 $11.30
22 TEETH H.D.
S391 $5.37
18 TEETH
3pc Timing Set
3-163S $42.71
INCLUDES [163], [S288] & [S289] H.D.
3-499S $31.69
INCLUDES [499], [S390] & [S391]
Continued on Next Page
Page 635. OLDSMOBILE (Continued)
Line
Part Title
Part No
Description
65
350-G & L ENG - 1977-79 - 8 Cyl. - 4.000 Bore (CHEVROLET)
(Continued)
HI VOL PUMP (20% ADDL VOL OF OIL) NOTE: THIS HI VOL PUMP
IS MANUFACTURED W/BOLT ON TYPE FLANGE AND A CHAMFERED HOLE.
EITHER A BOLT ON OR PRESS IN SCREEN CAN BE USED. DEPENDING
ON THE OIL PUMP SCREEN USED THIS OIL PUMP MAY BE USED IN
EITHER FRONT WHEEL DRIVE OR REAR WHEEL DRIVE APPLICATIONS
M22G $123.94
STOCK PUMP FOR FWD & RWD
Pump Kit
K22G $35.16
EXC. HI VOL
Screen Assy
22FHVS $44.92
BOLT ON SCREEN W/3/4" PICK UP TUBE- USE W/HI VOL PUMP- RWD
ONLY
22FS $31.75
PRESS IN SCREEN W/5/8" PICK UP TUBE, CAN BE USED IN EITHER
STOCK OR HI VOL PUMP- RWD ONLY
22-GS1
PRESS IN SCREEN- CAN BE USED IN STOCK OR HI VOL PUMP- FWD ONLY
Intermediate Shaft
IS22F $14.18
-
Camshaft
SOC12 $163.53
1978-1980 HYD.
Mell Lube
M10012 $4.93
-
Lifters
JB2065 $18.58
1978-1980 STANDARD HYD.
JB2066 $13.45
1978-1980 .010 OVERSIZE HYD.
JB2104 $15.84
HYD. ROLLER
Push Rods
MPR307 $2.62
1978-1979 EXC. ROLLER LIFTERS
MPR343 $2.09
1980 EXC. ROLLER LIFTERS
MPR358 $4.25
1978-1985 W/HYD. ROLLER LIFTERS
Intake Valve
V1370 $7.20
Head Dia. 1.875
Valve Springs
VS1100 $6.12
1981-1985
VS700 $6.16
1978-1980
Valve Locks
VL200 $1.21
-
Rocker Arms
MR890 $10.27
1978-1979
MR891 $3.58
1980-1985
Rocker Arm Kit
MRK540-1 $25.28
1978-1979 KIT INCLUDES 2-[MR-890] & 1-[MRM-1798] PIVOT
1961-1964 HI VOL PUMP (20% ADDL VOL OF OIL) NOTE: THIS
HI VOL PUMP IS MANUFACTURED W/BOLT ON TYPE FLANGE AND A
CHAMFERED HOLE. EITHER A BOLT ON OR PRESS IN SCREEN CAN
BE USED.
Pump Kit
K22F $42.79
1961-1964 EXC. HI VOL
Screen Assy
22FHVS $44.92
1961-1964 BOLT ON SCREEN W/3/4" PICK UP TUBE- USE W/HI
VOL PUMP
22FS $31.75
1961-1964 PRESS IN SCREEN W/5/8" PICK UP TUBE, CAN BE
USED IN EITHER STOCK OR HI VOL PUMP
Intermediate Shaft
IS22F $14.18
1961-1964
Mell Lube
M10012 $4.93
-
Push Rods
MPR91 $6.57
-
Valve Locks
VL200 $1.21
-
Chain
494 $22.07
48 LINKS
Cam Sprocket
S344 $44.41
36 TEETH
Crank Sprocket
S246 $39.56
1961-1964 18 TEETH
S301 $17.30
1959-1960 18 TEETH PARTIAL KEYWAY
Page 638. OLDSMOBILE (Continued)
Line
Part Title
Part No
Description
70
400 ENG - 1965-69 - 8 Cyl. - 4.000 Bore
-
Oil Pump
M22F $114.26
STOCK PUMP
M22FHV $181.07
HI VOL PUMP (20% ADDL VOL OF OIL) NOTE: THIS HI VOL PUMP
IS MANUFACTURED W/BOLT ON TYPE FLANGE AND A CHAMFERED HOLE.
EITHER A BOLT ON OR PRESS IN SCREEN CAN BE USED.
Pump Kit
K22F $42.79
EXC. HI VOL
Screen Assy
22FHVS $44.92
BOLT ON SCREEN W/3/4" PICK UP TUBE- USE W/HI VOL PUMP
22FS $31.75
PRESS IN SCREEN W/5/8" PICK UP TUBE, CAN BE USED IN
EITHER STOCK OR HI VOL PUMP
Intermediate Shaft
IS22F $14.18
-
Camshaft
MC1287 $249.39
1967 W/4BC EXC. O.A.I.
MC1287 $249.39
1968-1969 W/A.T. HYD.
ROC10 $113.01
1966-1967 W/O.A.I. (RAM AIR) HYD. OEM #402194 HI PERF.
Torque Camshaft
MTO1 $157.33
1968-1969 NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW-MID. PERF. CAM LIFT .280 INT.
.295 EXH. (EXC. HI PERF)
Torque Cam Lifter Kit
CLMTO1 $276.55
1968-1969 NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1- [MTO-1]
CAM, 16-[JB-951] LIFTERS & 4OZ MELL LUBE. CHECK FOR
COIL BIND. USE [VS-720] SPRING W/INSTALLED HGT. OF 1.67
CLASS I HYD. NOT COMPUTER COMPATIBLE. IMPROVES LOW-MID.
PERF. CAM LIFT .280 INT. .295 EXH.
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-310]
INNER SPRING W/INSTALLED HGT. OF 1.57 & [VS-450] OUTER
SPRING W/INSTALLED HGT. OF 1.59. CAM LIFT .280 INT. .295
EXH.
Torque Cam Lifter Kit
CLMTP1 $263.91
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTP-1] CAM, 16-[JB-951]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-310]
INNER SPRING W/INSTALLED HGT. OF 1.57 & [VS-450] OUTER
SPRING W/INSTALLED HGT. OF 1.59. CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .280 INT.
.295 EXH.
Mell Lube
M10012 $4.93
-
Lifters
JB951 $5.88
HYD.
Push Rods
MPR105 $2.53
-
Intake Valve
V1161 $13.91
Head Dia. 2.110
Exhaust Valve
V1245 $14.12
Head Dia. 1.660
Valve Springs
VS310 $4.39
INNER W/A.T. EXC. RAM AIR
VS450 $5.36
OUTER EXC. RAM AIR
Valve Locks
VL200 $1.21
-
Chain
350.
60 LINKS
3pc Timing Set
3-350S $60.36
INCLUDES [350], [S305] & [S371]
72
403 ENG - 1977-79 - 8 Cyl. - 4.351 Bore
-
Oil Pump
M22F $114.26
STOCK PUMP
M22FHV $181.07
HI VOL PUMP (20% ADDL VOL OF OIL) NOTE: THIS HI VOL PUMP
IS MANUFACTURED W/BOLT ON TYPE FLANGE AND A CHAMFERED HOLE.
EITHER A BOLT ON OR PRESS IN SCREEN CAN BE USED.
Pump Kit
K22F $42.79
EXC. HI VOL
Screen Assy
22FHVS $44.92
BOLT ON SCREEN W/3/4" PICK UP TUBE- USE W/HI VOL PUMP- RWD
ONLY
22FS $31.75
PRESS IN SCREEN W/5/8" PICK UP TUBE, CAN BE USED IN EITHER
STOCK OR HI VOL PUMP- RWD ONLY
22FS3 $19.48
PRESS IN SCREEN- CAN BE USED IN STOCK OR HI VOL PUMP- FWD ONLY
Intermediate Shaft
IS22F $14.18
-
Camshaft
SOC9 $166.79
HYD.
Camshaft Lifter Kit
CLSOC9 $261.09
KIT INCLUDES 1-[SOC-9] CAM, 16-[JB-951] LIFTERS & 4OZ MELL
LUBE
Torque Camshaft
MTO1 $157.33
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-720]
SPRING W/INSTALLED HGT. OF 1.67. CAM LIFT .280 INT. .295
EXH.
Torque Cam Lifter Kit
CLMTO1 $276.55
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTO-1] CAM, 16-[JB-951]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-720]
SPRING W/INSTALLED HGT. OF 1.67 CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .280 INT.
.295 EXH.
HI VOL PUMP (20% ADDL VOL OF OIL) NOTE: THIS HI VOL PUMP
IS MANUFACTURED W/BOLT ON TYPE FLANGE AND A CHAMFERED HOLE.
EITHER A BOLT ON OR PRESS IN SCREEN CAN BE USED.
Pump Kit
K22F $42.79
EXC. HI VOL
Screen Assy
22FHVS $44.92
BOLT ON SCREEN W/3/4" PICK UP TUBE- USE W/HI VOL PUMP- RWD
ONLY
22FS $31.75
PRESS IN SCREEN W/5/8" PICK UP TUBE, CAN BE USED IN EITHER
STOCK OR HI VOL PUMP- RWD ONLY
22FS1 $29.81
PRESS IN SCREEN CAN BE USED IN EITHER STOCK OR HI VOL PUMP- FWD
ONLY
Intermediate Shaft
IS22F $14.18
-
Camshaft
MC1287 $249.39
1966 TORONADO ONLY
MC1287 $249.39
1967 EXC. H.P. HYD.
Camshaft
ROC10 $113.01
1967 39¦ LIFTER ANGLE W/H.P. HYD.
Mell Lube
M10012 $4.93
-
Lifters
JB951 $5.88
HYD. EXC. TORONADO
Push Rods
MPR301 $2.34
9.594 length EXC. TORONADO
MPR333 $2.73
9.622 length EXC. TORONADO
MPR98B $6.98
TORONADO ONLY
Intake Valve
V1002 $9.32
Head Dia. 2.072 TORONADO ONLY W/.3428 STEM DIA.
V1457 $9.62
Head Dia. 1.995 SPEC. HI PERF. 1965-67 ONLY
Exhaust Valve
V0974 $14.20
Head Dia. 1.624 1965-67 TORONADO & 1965 & 1967 SPEC.
HI PERF.
HI VOL PUMP (20% ADDL VOL OF OIL) NOTE: THIS HI VOL PUMP
IS MANUFACTURED W/BOLT ON TYPE FLANGE AND A CHAMFERED HOLE.
EITHER A BOLT ON OR PRESS IN SCREEN CAN BE USED.
Pump Kit
K22F $42.79
EXC. HI VOL
Screen Assy
22FHVS $44.92
BOLT ON SCREEN W/3/4" PICK UP TUBE- USE W/HI VOL PUMP- RWD
ONLY
22FS $31.75
PRESS IN SCREEN W/5/8" PICK UP TUBE, CAN BE USED IN EITHER
STOCK OR HI VOL PUMP- RWD ONLY
Screen Assy
22FS1 $29.81
PRESS IN SCREEN CAN BE USED IN EITHER STOCK OR HI VOL PUMP- FWD
ONLY
Intermediate Shaft
IS22F $14.18
-
Camshaft
MC1287 $249.39
1968-1975 EXC. H.P. & 442
MC1287 $249.39
1976 EXC. H.P. HYD.
ROC10 $113.01
W/H.P. HYD.
Torque Camshaft
MTO1 $157.33
NOT CALIFORNIA COMPLIANT. CLASS I HYD. NOT COMPUTER COMPATIBLE.
IMPROVES LOW-MID. PERF. CHECK FOR COIL BIND. USE [VS-720]
SPRING W/INSTALLED HGT. OF 1.67. CAM LIFT .280 INT. .295
EXH.
Torque Cam Lifter Kit
CLMTO1 $276.55
NOT CALIFORNIA COMPLIANT. KIT INCLUDES 1-[MTO-1] CAM, 16-[JB-951]
LIFTERS & 4OZ MELL LUBE. CHECK FOR COIL BIND. USE [VS-720]
SPRING W/INSTALLED HGT. OF 1.67 CLASS I HYD. NOT COMPUTER
COMPATIBLE. IMPROVES LOW- MID. PERF. CAM LIFT .280 INT.
.295 EXH.
Mell Lube
M10012 $4.93
-
Lifters
JB951 $5.88
HYD.
Push Rods
MPR327 $2.45
-
Intake Valve
V1002 $9.32
1968-1971 Head Dia. 2.072 HI PERF. POLICE & TORONADO
V1002 $9.32
1972 Head Dia. 2.072 F85 W/MANUAL TRANS. OR O.A.I.
V1002 $9.32
1973 Head Dia. 2.072 CUTLASS & VISTA CRUISER W/OPTIONAL L77
& TURBO HYD. 400 TRANS.
V1002 $9.32
1973 Head Dia. 2.072 M.T.
V1002 $9.32
1974 Head Dia. 2.072 W/W30 OPTION
V1457 $9.62
1968-1971 Head Dia. 1.995 EXC. HI PERF. POLICE & TORONADO
V1457 $9.62
1973-1976 Head Dia. 1.995 EXC. MAN. TRANS., CUTLASS &
VISTA CRUISER & TURBO HYD. 400 TRANS. & 1974 W/W30 OPTION
Exhaust Valve
V0974 $14.20
1968-1972 Head Dia. 1.624
V0974 $14.20
1973 Head Dia. 1.624 CUTLASS & VISTA CRUISER W/OPTIONAL L77
& TURBO HYD. 400 TRANS.
